This is HWGC OFFICIAL Flagship Store Directly supply smt machine HW-T4-50F Pick and place machine
1. The heating system adopt the Swedish nickel heater with efficiency and energy-saving. The peak wave length of the radiation power is 4UM with curved surface reflector enhance temperature ramp up speed, improve the thermal efficiency. And the special forced-air circulation system make PCB and the component uniformly heated and eliminate the "shadow effect" efficiently.
2. Using special high temperature resistant protection material in heating preservation structure and cast iron in heating passage.
3. Using imported Taiwan SanYue long shaft high temperature blower motor and W shaped heat duct, critical design for no noise or vibration and convenient for maintenance .
4. Heating zones are structured with porous aluminum air director, hot air is uniformly distributed to the PCB surface. Hood can open completely so as to easily proceed maintenance.
Pick And Place Machine , Chip Mounter Surface Mounter , Smt Machine
porduct description
The HW-T8-80F is our most popular model with Vision. The HW-T8-80F offers technologically advanced features with 260mm x 400mm work area, 80 single feeder positions (up to 120 feeders using bank feeders) where quick setup, easy of operation and high reliability are paramount.
System Features
* The highest quality with the most advanced equipment at a cost-effective solution
* Placement rates up to 13000-15000 cph
* Accurately places a wide range of components including 0201, 0402, LED, BGA, QFN...
The HW vision System assist allows accurate placement of 0201, BGA, QFN, QFP,LED and a wide range of virtually all SMT components.
|
Products Description
|
|
Specification
|
|
Maximum circuit board area
|
400*200 mm
|
|
Number of mounting heads
|
4
|
|
Maximum movement range of Z axis
|
20 mm
|
|
Maximum mounting rate
|
9,500 PCS/hour
|
|
Average mounting rate
|
8,000 PCS/hour
|
|
Positioning accuracy
|
0.001mm
|
|
Buffering range of suction nozzle
|
4.5mm
|
|
Power supply
|
220V/110V, 50 Hz
|
|
Compressed air:
|
0.6-0.7 Mpa
|
|
Average power
|
400 W
|
|
Recognition Mode
|
Four Heads Synchronized Recognition
|
|
Number of cameras
|
one Mark camera, four high-speed cameras, a high-definition camera
|
|
Product weight
|
400kg
|
|
PCB access mode
|
automatic Left-in and right-out access, supporting left-right device connection function
|
|
Quantity of trays
|
Up to 48 non-feeder feeding components are supported, each of which can specify its coordinates within the mounting range.
|
|
Complex speed to mount resistance and Chip
|
7000/CPH
|
|
Mounting accuracy range
|
0201-40*40mm,Pin spacing 0.3mm
Chip(Matching which support electric feeder can mount the 0402,0201)
|
|
Quantity of feeders
|
50pcs
|
|
Service motor
|
Panasonic servo moto
|
|
|
Guide rail
|
|
Taiwan TBI Linear Guide rail
|
|
|
Nozzle Vacuum Source
|
Japan CKD High Speed On-off Vacuum Generator with Vacuum Damage
|
|
|
Minimum air capacity of pump
|
80-120 L/min, volume more than 60 L
|
|
|
Gas quality requirements
|
oil-water separation device, dust filter device, air pressure stabilization device
|
|
|
Dimension
|
900×1140×900mm
|
|
Vision System
The HW-series vision pick and place systems is easy to programming for all operators, Intelligent and fast to operation
Feeders
Yamaha Pneumatic feeder and Electricial feeder were adopted, sizes include 8mm, 12mm, 16mm, 24 mm, 32mm and 44mm.
